Have you ever wanted to display your favorite armor sets in all their glory without having to wear them yourself? Or perhaps you’re looking for a way to store your spare armor without it taking up too much space. Whatever your reason, an armor stand is the perfect solution. And the best part is, you can easily make one yourself with a few simple materials.
To make an armor stand, you will need the following materials:
- A piece of wood or metal (at least 2 feet tall and 1 foot wide)
- A saw
- A drill
- Screws or nails
- A piece of foam or cardboard (optional)
Once you have gathered your materials, you can begin assembling your armor stand. First, cut the piece of wood or metal to the desired size. Then, drill a hole in the center of the top of the stand. This hole is where you will insert the armor’s hanger.
Next, you need to create a base for the stand. This can be done by attaching a piece of wood or metal to the bottom of the stand. The base will help to keep the stand upright and prevent it from wobbling. If you are using a piece of foam or cardboard, you can simply glue it to the bottom of the stand. Finally, insert the armor’s hanger into the hole in the top of the stand. You can now hang your armor on the stand and display it with pride.
Gather Your Materials
Birch Wood Planks
You will need six birch wood planks to create an armor stand. These can be obtained by chopping down birch trees with an axe and collecting the dropped wood. Birch trees can be identified by their white bark and diamond-shaped leaves.
Iron Ingots
You will need four iron ingots to create an armor stand. These can be obtained by smelting iron ore in a furnace using coal or charcoal as fuel. Iron ore can be found in caves, mines, and on the surface of the earth.
Crafting Table
You will need a crafting table to combine the birch wood planks and iron ingots into an armor stand. Crafting tables can be created by combining four wooden planks in a square shape on a crafting grid.
Materials for the Armor Stand
| Material | Quantity |
|---|---|
| Birch wood planks | 6 |
| Iron ingots | 4 |
Prepare the Wooden Poles
For the base of your armor stand, you will need two wooden poles that are each approximately 36 inches long. You can use any type of wood you like, but pine or cedar are good choices because they are both lightweight and durable.
Once you have your wooden poles, you need to prepare them for assembly. First, cut a notch into the top of each pole, about 2 inches from the end. The notch should be about 1 inch wide and 1/2 inch deep. This notch will be used to hold the crossbar in place.
Drill Holes for the Crossbar
Next, you need to drill holes for the crossbar. The crossbar will be used to connect the two poles together. To drill the holes, measure 12 inches from the top of each pole and mark the spot. Then, use a drill bit that is slightly smaller than the diameter of the crossbar to drill a hole through each pole. The holes should be about 1/2 inch deep.
Sand and Seal the Poles
Once you have drilled the holes, you need to sand the poles to smooth out any rough edges. You can use a sanding block or sandpaper to do this. Once the poles are sanded, you can seal them with a clear sealant to protect them from the elements.
| Material | Quantity |
|---|---|
| Wooden poles | 2 |
| Crossbar | 1 |
| Wood screws | 4 |
Cut the Wooden Dowels
The next step is to cut the wooden dowels to the desired lengths. The dimensions for the standard armor stand are as follows:
| Dowel Size | Length |
|---|---|
| 4 x 1/4 inch | 16 inches (4) |
| 3/8 inch | 24 inches (1) |
| 1/4 inch | 18 inches (1) |
For a larger stand, you can increase the length of the dowels proportionally. Use a sharp saw to ensure clean cuts and avoid any splintering or tearing of the wood.
Before cutting, it’s essential to measure and mark the dowels accurately. This will ensure that all the components fit together properly and the stand is stable. Once cut, ensure that the edges are smooth and free of any rough spots or burrs that could interfere with assembly or aesthetics.
Join the Horizontal Poles
Now that you have all of the pieces cut to size, it’s time to start assembling the armor stand. Start by joining the two horizontal poles together. To do this, you will need to drill two holes into each pole, one on each end. The holes should be big enough to fit the dowels that you will be using to connect the poles.
Once you have drilled the holes, insert the dowels into the holes and glue them in place. Make sure that the dowels are flush with the ends of the poles. Once the glue has dried, the two horizontal poles will be securely joined together.
Next, you will need to attach the vertical poles to the horizontal poles. To do this, you will need to drill two holes into each vertical pole, one on each end. The holes should be big enough to fit the dowels that you will be using to connect the poles.
Once you have drilled the holes, insert the dowels into the holes and glue them in place. Make sure that the dowels are flush with the ends of the poles. Once the glue has dried, the vertical poles will be securely attached to the horizontal poles.
| Horizontal Pole Measurements | Vertical Pole Measurements |
|---|---|
| 2″ x 2″ x 36″ | 2″ x 2″ x 18″ |
Make the Base
The base is the foundation of your armor stand, so it’s important to make it sturdy. You can use a variety of materials for the base, depending on what you have available and how much weight you want the stand to support.
Here are a few tips for making a sturdy base:
- Use a heavy material, such as metal, concrete, or wood.
- If you’re using wood, be sure to seal it to protect it from moisture.
- Make the base wide enough to provide a stable footing for the armor stand.
Here is a simple step-by-step guide to making a base for your armor stand:
- Cut a piece of wood or metal to the desired size for the base.
- Mark the center of the base and drill a hole for the pole.
- Insert the pole into the hole and secure it with screws or bolts.
- Attach the base to the ground using screws, bolts, or stakes.
Materials for the Base
| Material | Advantages | Disadvantages |
|---|---|---|
| Metal | Durable, sturdy | Heavy, expensive |
| Concrete | Sturdy, inexpensive | Heavy, difficult to work with |
| Wood | Lightweight, easy to work with | Not as durable as metal or concrete |
Connect the Vertical and Horizontal Poles
Once you have assembled the base, it’s time to connect the vertical and horizontal poles. Here’s a step-by-step guide:
Step 1: Insert the Vertical Pole into the Base
Locate the bottom of the vertical pole, which should have a hole drilled into it. Carefully insert the pole into the center hole of the base and push it down until it is flush with the surface of the base.
Step 2: Secure the Pole with Screws
Take the four screws provided and insert them through the holes in the base and into the vertical pole. Tighten the screws securely using a screwdriver, ensuring that the pole is stable and does not wobble.
Step 3: Insert the Horizontal Poles
Locate the two horizontal poles. Each pole should have two holes drilled into it, one on each end.
Step 4: Align the Holes
Hold a horizontal pole vertically and align the hole on one end with the hole near the top of the vertical pole. Repeat this process for the other horizontal pole, aligning it with the hole near the bottom of the vertical pole.
Step 5: Insert the Dowel Rods
Take the two dowel rods and cut them to the desired length. Insert one dowel rod into each hole in the horizontal poles. The dowel rods will act as support for the armor.
Step 6: Slide the Poles Together
Slide the horizontal poles onto the dowel rods, aligning them so that the holes in the poles line up with the holes in the vertical pole. Carefully push the poles together until they are fully inserted and flush with the vertical pole.
| Step | Description |
|---|---|
| 1 | Insert vertical pole into base |
| 2 | Secure pole with screws |
| 3 | Insert horizontal poles |
| 4 | Align holes |
| 5 | Insert dowel rods |
| 6 | Slide poles together until aligned and flush with vertical pole |
Step 7: Secure the Horizontal Poles
Use the remaining four screws to secure the horizontal poles to the vertical pole. Tighten the screws securely to ensure a stable and sturdy frame.
Reinforce the Joints
To make your armor stand sturdier, you can reinforce the joints with glue or other adhesives. This will help to prevent the stand from wobbling or collapsing under the weight of your armor. To reinforce the joints, follow these steps:
1.
Apply a small amount of glue to the inside of each joint.
Use a toothpick or cotton swab to apply the glue evenly. Be careful not to use too much glue, as this can make the stand difficult to assemble.
2.
Assemble the stand according to the instructions.
Once you have applied the glue, assemble the stand according to the instructions. Make sure to press the joints together firmly to ensure a good bond.
3.
Allow the glue to dry completely.
Before you use the stand, allow the glue to dry completely. This will help to ensure that the joints are strong and secure.
4.
Test the stand before using it.
Once the glue has dried, test the stand before using it. Make sure that the stand is stable and can support the weight of your armor. If the stand is wobbly or collapses, you may need to reinforce the joints further.
By following these tips, you can reinforce the joints of your armor stand and make it more durable and long lasting.
Reinforcement Options
There are a variety of adhesives that you can use to reinforce the joints of your armor stand. Some of the most common options include:
| Adhesive | Pros | Cons |
|---|---|---|
| Wood glue | Strong and durable | Can be difficult to apply |
| Epoxy | Very strong and durable | Can be difficult to apply |
| Cyanoacrylate glue (super glue) | Quick and easy to apply | Not as strong as wood glue or epoxy |
Paint or Seal the Armor Stand
Once the armor stand is sanded to your liking, you can paint or seal it to protect the finish. If you are painting the stand, use a primer first to help the paint adhere. Then, paint the stand with your desired color of paint. You can use acrylic paint, spray paint, or any other type of paint that you like. Once the paint is dry, you can seal it with a clear coat of polyurethane or varnish to protect it from scratches and wear.
If you are not painting the stand, you can still seal it with a clear coat of polyurethane or varnish to protect the finish. This will help to prevent the wood from warping or cracking.
Here are some tips for painting or sealing an armor stand:
- Use a primer before painting to help the paint adhere.
- Use a light, even coat of paint.
- Allow the paint to dry completely before sealing it.
- Use a clear coat of polyurethane or varnish to protect the finish.
Here is a table of the materials you will need:
| Material | Quantity |
|---|---|
| Armor stand | 1 |
| Sandpaper | Assorted grits |
| Primer | 1 can |
| Paint | 1 can |
| Clear coat | 1 can |
Add Hooks or Accessories
To further customize your armor stand, you can add hooks or accessories to display additional items or enhance its functionality. Here are some ideas:
Hooks
Hooks can be attached to the stand’s arms or base to hang weapons, shields, or other gear. You can use metal hooks, screw-in hooks, or self-adhesive hooks, depending on the weight of the items you want to hang.
Weapon Grips
Weapon grips can be attached to the stand’s hands to securely hold swords, axes, or other weapons. This provides a realistic display and prevents the weapons from falling off.
Magnets
Magnets can be glued or attached to the stand’s surface to hold small accessories like jewelry, pendants, or coins. This allows for easy display and removal of these items.
Shelves
Small shelves can be added to the stand’s base or arms to display additional items like potions, scrolls, or books. This can create a more immersive and detailed display.
Lighting
LED lights can be incorporated into the stand’s base to illuminate the armor from below. This creates a dramatic effect and highlights the details of the armor.
Here’s a table summarizing the different accessories you can add to an armor stand:
| Accessory | Purpose | Attachment Method |
|---|---|---|
| Hooks | Hang weapons, shields, or gear | Metal hooks, screw-in hooks, self-adhesive hooks |
| Weapon Grips | Securely hold weapons | Glue, screws, or clamps |
| Magnets | Hold small accessories | Glue or magnets |
| Shelves | Display additional items | Screws or glue |
| Lighting | Illuminate the armor | LED lights, glue, or magnets |
Perfect Your Armor Display
Displaying your armor can be a great way to show off your accomplishments and keep your gear organized. An armor stand is a great way to do this, and it’s easy to make one yourself.
Here’s what you’ll need:
- A piece of plywood (at least 24″ x 36″)
- A saw (circular saw, jigsaw, or hand saw)
- A drill
- A screwdriver
- Wood screws (1″ – 1 1/2″)
- Sandpaper or sanding sponge
- Paint or stain (optional)
Here’s how to make it:
- Cut the plywood into two pieces, each 12″ x 36″.
- Drill a hole in the center of each piece of plywood, about 1″ from the edge.
- Insert a wood screw into each hole, leaving about 1/2″ of the screw exposed.
- Place the two pieces of plywood together, with the screws facing each other.
- Screw the two pieces of plywood together, using the wood screws.
- Sand the edges of the armor stand to smooth them out.
- Paint or stain the armor stand, if desired.
- Allow the armor stand to dry completely.
- Place your armor on the armor stand and enjoy!
10. Tips for Making a Great Armor Stand
Here are a few tips for making a great armor stand:
Use sturdy materials. The armor stand will need to be able to support the weight of your armor, so make sure to use sturdy materials like plywood or metal.
Make sure the stand is the right size. The stand should be tall enough to accommodate your armor, and it should be wide enough to provide a stable base.
Consider the weight of your armor. If you have heavy armor, you’ll need to make sure that the stand is sturdy enough to support it.
Consider the style of your armor. The stand should complement the style of your armor.
Make sure the stand is stable. The stand should be able to stand up on its own without tipping over.
Use a variety of materials. You can use a variety of materials to make an armor stand, such as wood, metal, or plastic.
Be creative. There are no rules when it comes to making an armor stand, so be creative and come up with your own unique design.
How To Make A Armor Stand
To make an armor stand, you will need the following materials:
- 1 wooden pole (at least 5 feet tall)
- 4 wooden blocks (each about 6 inches square)
- 8 wood screws
- 1 drill
- 1 screwdriver
Instructions:
- Cut the wooden pole to the desired height.
- Attach the wooden blocks to the bottom of the pole, evenly spaced around the perimeter.
- Drill pilot holes into the blocks and the pole.
- Secure the blocks to the pole with wood screws.
- Allow the glue to dry completely.
- Your armor stand is now complete!
People Also Ask About How To Make A Armor Stand
How tall should an armor stand be?
Armor stands should be at least 5 feet tall to accommodate most suits of armor.
What type of wood is best for making an armor stand?
Hardwoods such as oak, maple, or birch are best for making armor stands as they are strong and durable.
Can I use PVC pipe to make an armor stand?
Yes, you can use PVC pipe to make an armor stand, but it is not as strong as a wooden armor stand.
