Removing a car windscreen can be a daunting task, but it is not as difficult as it may seem. With the right tools and a little patience, you can remove your windscreen in a few hours. If you are replacing your windscreen yourself, you must remove the old one before you can install the new one. In this article, we will provide you with step-by-step instructions on how to remove a car windscreen. We will also provide you with some tips and tricks to make the process easier.
The first step is to remove the trim around the windscreen. This is usually held in place by clips, screws, or bolts. Once the trim is removed, you will need to remove the bolts that hold the windscreen in place. These bolts are usually located around the perimeter of the windscreen. Once the bolts are removed, you will be able to carefully lift the windscreen out of the car. Be sure to wear gloves and safety glasses when removing the windscreen, as it can be heavy and sharp.
Once the windscreen is removed, you will need to clean the frame. This will help to ensure that the new windscreen is properly sealed. You can clean the frame with a mild detergent and a soft cloth. Once the frame is clean, you can install the new windscreen. The process of installing a new windscreen is the reverse of the removal process. First, you will need to place the new windscreen in the frame. Then, you will need to bolt the windscreen in place. Finally, you will need to replace the trim around the windscreen. Once the new windscreen is installed, you will need to allow it to cure for 24 hours before driving the car.
Lifting the Windscreen
Now that you have removed some of the components and have access to the windscreen, it’s time to remove it. But you can’t just pull it out; you need to lift it off carefully. Here’s how to do it:
1. **Remove the bolts that hold the windscreen in place**. There should be four bolts, two on each side. Use a socket wrench or a spanner to loosen them but don’t remove them completely just yet.
2. **Cut the sealant around the windscreen**. Use a sharp knife or a utility knife to cut through the sealant that goes around the windscreen. Be careful not to cut into the windscreen itself.
3. **Insert a suction cup lifter onto the windscreen**. This will help you lift the windscreen off the car body. Position the suction cup lifter in the center of the windscreen.
4. **Lift the windscreen off the car body**. Once the bolts are loosened and the sealant is cut, you can start lifting the windscreen off the car body. Do this slowly and carefully, as the windscreen is heavy. Have a helper assist you if possible.
| Caution |
|---|
| Don’t lift the windscreen off the car body by yourself, as it is heavy and can be dangerous. Always have a helper assist you. |
5. **Once the windscreen is lifted off the car body, place it on a soft surface**. This will help protect it from getting scratched or damaged.
How To Remove Car Windscreen
Removing a car windscreen is a task that requires some skill and care. If you’re not comfortable working on your car, it’s best to leave this job to a professional. However, if you’re confident in your abilities and have the right tools, it’s possible to remove the windscreen yourself.
Here are the steps on how to remove a car windscreen:
- Park your car on a level surface and turn off the engine.
- Protect the interior of your car. Use masking tape to cover any exposed wires or trim around the windscreen.
- Remove the windscreen wipers. This is usually done by popping off the caps at the base of the wiper arms and then pulling the arms off the windscreen.
- Cut the urethane sealant around the windscreen. Use a sharp razor blade or a utility knife to score the sealant around the edge of the windscreen. Be careful not to cut into the glass.
- Remove the windscreen. Once the sealant has been cut, the windscreen can be removed. To do this, have a helper hold the windscreen from the inside while you carefully pry it loose from the outside. Use a plastic pry bar or a suction cup to avoid damaging the glass.
- Clean the windscreen frame. Once the windscreen has been removed, clean the frame thoroughly. Remove any old sealant or debris that may be present.
- Apply new sealant. Apply a bead of new urethane sealant around the edge of the windscreen frame. Be sure to follow the manufacturer’s instructions for applying the sealant.
- Install the windscreen. Carefully position the windscreen in the frame and press it into place. Have a helper hold the windscreen from the inside while you secure it from the outside. Use several clamps to hold the windscreen in place while the sealant cures.
- Reinstall the windscreen wipers. Once the sealant has cured, reinstall the windscreen wipers. Be sure to tighten the nuts or bolts that hold the wipers in place.
People Also Ask About How To Remove Car Windscreen
How much does it cost to remove a car windscreen?
The cost to remove a car windscreen varies depending on the make and model of your car, as well as the location of the shop. However, you can expect to pay anywhere from $200 to $500 for the removal and installation of a new windscreen.
Can I remove a car windscreen myself?
Yes, it is possible to remove a car windscreen yourself. However, it is important to note that this is a delicate task that requires some skill and care. If you are not comfortable working on your car, it is best to leave this job to a professional.
What tools do I need to remove a car windscreen?
To remove a car windscreen, you will need the following tools:
- A sharp razor blade or a utility knife
- A plastic pry bar or a suction cup
- A new urethane sealant
- Clamps
